admin_pps
Most of the commonly reported issues and questions are answered in the Frequently Asked Questions (FAQ) option under the Support menu of this website.
*** PLEASE NOTE ***
Your forum account is not the same as the account used in the shop. They are completely separate accounts.
Your forum account is not the same as the account used in the shop. They are completely separate accounts.
1st December: A new version of the GoFlight Interface Tool for MSFS is now available.
12th November: A new version of the GoFlight Interface Tool for X-Plane is now available.
6th June: A new version of Virtual Flight Sim Hardware is now available (huge update)
21st November: A new version of the GoFlight Interface Tool for FSX/FSXSE/P3D is now available.
admin_pps
Comments
-
Do you have a recent backup of Documents\GoFlight Interface Tool?
-
Does it lockup on the initial P2D start screen or when the aircraft VC is displayed? Best wishes Steve
-
The flickering is normal and indicates data being received. Double check the events and event actions for trim up and make sure they are correct. If you clicked Default FS then they should be fine, but no harm in clicking that button again if you didn't make any other changes to the LGT config. Assuming it does the same…
-
Done via your enquiry email.
-
I'm working on this amongst some other things that people need/asked for. Best wishes Steve
-
Its located in Documents\GoFlight Interface Tool. If its not there, reinstall GIT. Best wishes Steve
-
Ok, I can replicate what you are seeing. Its a very weird bug caused by the way you are running GIT. Usually GIT is started before P3D or during the scenerio screen and then the vehicle is selected etc. I will add it to my to do list to fix, but in the meantime, start GIT as above and all should be good. Also, address the…
-
"But the relevant GoFlight executable is loaded so my GF166s and MCP becomes alive. Frequencies are shown on both 166 units." If GIT isn't running at the point, why are these lit up? The GIT module cannot do this that is loaded into P3D, so either GIT is running, or something else is driving them, like GoFlights own…
-
Yes, I think its when the sim is paused or the aircraft change triggers a pause and then the switch over is not detected. Can you confirm that's the case?
-
Awesome! Since you have A24 firmware, you can set the Write and Cmd Delay sliders on the GIT MCPPRO tab to 0. That should help with any delays. Not sure about the pin outs. Usually there is a part number on the encoder. Just google for the part number and you should be good. Best wishes Steve
-
You may be able to simply clean it. See from 3 minutes in on this vid: https://www.youtube.com/watch?v=lylpr1anaLg&t=182s&ab_channel=Astro%27sElectronicsLab Best wishes Steve
-
I have reset the server cache and the enquires form is working correctly now. I cannot find your account using the email address you have registered on the forum. Can you PM me or use the enquires form to provide the correct email address. Thx Steve
-
There is a fix for FSUIPC in your account downloads. FSUIPC 64 bit never implemented a TCP/IP sockets server which GIT uses. The fix provides a 64bit server for FSUIPC. I will check at my end and see if I can replicate the issue. Best wishes Steve
-
You need the to be in the virtual cockpit before GIT will connect with the aircraft. The scenerio screen will not trigger the correct notification to GIT. Best wishes Steve
-
Can you post your GIT log when this happens. Thx Steve
-
Agreed. I will do that, but people were pressing me for a quick change as its now required for VATSIM. I'm OK. Took a long xmas break and then was sick for a while. Best wishes Steve
-
You may have faulty rotary encoders. Use GoFlights test software to see if the rotary is jumping around: https://1drv.ms/u/s!AvmOqBMETlayh9ZQUzSikUTgvmwIyw?e=CGwI4E Best wishes Steve
-
Use Detective and enable event monitoring. Then use the OBS knob in the virtual cockpit and the event to use should appear in the Detective monitoring window. Best wishes Steve
-
Use Event EVT_EFIS_CPT_RANGE and assign ROTATE as the action. Best wishes Steve
-
Your button was probably sticking and causing the problem. Best wishes Steve
-
Done. Please use the enquiry form on the contact page of the website for a quicker response for these type of requests. Best wishes Steve
-
It looks like GIT cannot read the PMDG GIT config xml file because of the inner exception of "The cloud file provider is not running". Do you have your Documents directory in the cloud and are your cloud services running? Best wishes Steve
-
I have reset your install counts for both copies of GIT. The user keys will work now with GIT FS2020. Best wishes Steve
-
Sorry for the late reply. I haven't been available for a few weeks. That info should be sufficient to add support. Best wishes Steve
-
Login to your account and download GIT for FS2020 as its always the latest version. Best wishes Steve
-
Its the aircraft that decides what to do when those Events fire. Best wishes Steve
-
Difficult to say. What hardware do you have that is configured to change the barometer? Best wishes Steve
-
On the GIT Log tab. You can add /log to the GIT icon for a txt file output. Best wishes Steve
-
What do you have in the 46O tab as you need a variable in there for anything to display? Best wishes Steve
-
I'm looking into it. Best wishes Steve