RogerDee
Most of the commonly reported issues and questions are answered in the Frequently Asked Questions (FAQ) option under the Support menu of this website.
*** PLEASE NOTE ***
Your forum account is not the same as the account used in the shop. They are completely separate accounts.
Your forum account is not the same as the account used in the shop. They are completely separate accounts.
1st December: A new version of the GoFlight Interface Tool for MSFS is now available.
12th November: A new version of the GoFlight Interface Tool for X-Plane is now available.
6th June: A new version of Virtual Flight Sim Hardware is now available (huge update)
21st November: A new version of the GoFlight Interface Tool for FSX/FSXSE/P3D is now available.
RogerDee
Comments
-
Off to the sun for a week or so. Will try again later. Many thanks for your support. Roger
-
Tried all the above. Still the same. What is odd I have plugged in an old Saitek AP panel and IAS and VS can be set from it. The MCP and PFD and Saitek all sync together. Unpluged Saitek and back to the situation where info is received from the PFD but none is sent back from the MCP for those two functions. Will put the…
-
Thanks for prompt reply. Your .jpg is most helpful. The problem I have is that the wheel on the MCP and the Dash are linked, but in IAS or VS mode I have to use the wheel on the Dash to adjust the values. Once the wheel on the Dash is rotated, then the approprate display on the MCP is activated. As most things work do you…
-
Thanks once again for your efforts.Have downloaded and installed the latest version and note the following. On the MCP pressing the speed button brings up 30 and IAS 30 on the PFD. Rotary on the MCP does not change these values,( it used to). V!, V2 etc work when the rotary is pressed. V speed on the thumb wheel. When…
-
On the Dash8 the Elevator trim and Aileron controls are reversed.If I try the PMDG 737, then the Elevator and Aileron controls work as expected. I have tried to reverse the function using the GF config tool no luck. Without changing the wiring on the LGT module can this be reversed for the Dash? Regards Roger
-
Many thanks. Works a treat. Roger
-
Hope I have attached correctly. Many thanks for your time.Roger
-
All previous events removed.Dome Light.Following set. Q400_DOMELIGHT=0and OHD_PNL_LIGHTS_DOME_SW=0Above for DOME_lights_ONand as above but =1 for DOME_light_OFFWith Switch 1 onT8 operated(down) Dome switch operates. Putting switch up cause various events in GIT dropdown menu to flash pass. Always seems to end up at…
-
There is something odd going on. One of the cockpit lights is also operating. I am going to delete all my various efforts and now that I understand the principles start again. Roger
-
The scrolling is the drop down menu in GIT
-
I have allredy tried that, but on selecting OFF and operating switch the drop down menu starts to scroll through all the options. Set it back to the OFF switch position and it works ONCE , then back to scrolling. I have assigned OHD-EXT-LT-LOGO-SW=0 to a seperate entry LOGO_light_OFF is this correct Roger
-
I now have two entries.OHD-EXT-LT-LOGO-SW=1 andOHD-EXT-LT-LOGO-SW=0 GF T8 switch1 set to event ON and action NOTHINGLogo switch on OHP set to ON, then GF switch moved to up position Light switch operates. Now confused how to set a second function to this switch. Roger
-
With clean install P3D V2.5 works just fine. Again, many thanks for you patience and expert help. Regards Roger
-
Many Thanks. . I have settled for the moment on 2.5 Will report back this pm. Regards Roger
-
Have just installed latest version of GIT. Dective does not crash.All the 7 segment displays on the MCP are at 0.ON the MCV tab The MCP and EFIS are recognised, but the import buttons are grey. In my Documents\Goflight the only entries are for the A320. Roger
-
Windows 7 64 bit and Dash 8 Pro installed. (incuding latest beta update) Whilst I do not understand the problem I observe some differences between P3D 2.4 and 3.1 and GIT. In 2.4 the field bottom right of Detective shows: MJC_ADC_Baro_L_CW This works with…
-
Have tried both Pilot and Pro with similar results. Must be something corrupt in me machine. Will re format and start again next week sometime. Roger
-
OK thanks. Will reinstall SSD some time next week.Thanks Roger
-
I have tried the pro and Pilot version. Have re installed Pilot version a couple of times. At present using the Pilot version. I have also re- installed 3.1 and ran a repair on Win 7 64 bit. Roger
-
No Win 7. Still puzzled why 2.4 is OK and not 3.1Roger
-
downloaded file from Slayer. Same error message!Roger Have tried again, same error code. Probable somthing weird in my computer. Propose when I have time to re format spare ssd and try again. Many thanks for all your efforts. Back to P3D V2.4! Roger
-
downloaded file from Slayer. Same error message!Roger
-
Have delered GIT and re downloaded the mjj file in downloads. Still get the same error message as above re Boolean etc. Going to swap ssds now as I am due on line in a while . Roger
-
I have used that download before my previous post. Still do not understand why everthing is fine in P3D V2.4 Roger
-
Opened the file in word pad. Just a load of stuff that makes no sense to me..On clicking on dective the file shown as needed is mjc8q400 . click on import get the following. The event "MJC_ADC_Baro_LCW" has errored:System.ArgumentOutOfRangeException: Specified argument was out of range of valid…
-
I have the same problem with the 737. there is a tick in the P3D box and no others. Where can I find this .ini file and where does it need to go. Using .18 version of GIT, OS + win 7, P3D V3.1 Roger
-
Steve. Thanks for your patience and tech knowledge. Seems to be OK now. SHMBO wants to go shopping this pm so will try and load the a320 stuff this pm. Regards Roger
-
Both products in the same folder.Double click GIT and computer is locked, cannot close git only option to switch off computer. Have tried several times with same result. Regards Roger
-
Unfortunatly my pal has to go away on business so I have had a play!Downloaded the GoFlight config tool (2.26.1) and BINGO all my modules are recognized and I have programmed a couple of functions on each module and the A320 reacts to them.Modules are: EFIS WP-6 T8-2 RP48 It therefore seems to me that GIT is not compatable…
-
That makes no difference. Seems to me that V3.1 "recognises" GIT but none of the modules are being recognized. I hope to have more info after my pal has had a look. Happy new year. Roger